Noise Emitter From Curves

Converts line/curve paths (roads, railways) into calibrated discrete point emitters whose source levels preserve total road acoustic energy independent of divide spacing.

Site Analysis Nickname: NoiseLines

Overview

Noise Emitter From Curves transforms linear infrastructure (motorways, urban arterials, local streets, railways) into discrete point emitters ready for acoustic propagation simulation.

Unlike naive subdivision where dividing curves into more points artificially inflates noise, this component employs analytical line-source calibration. Each discretized segment's sound power is calibrated such that the energetic summation of all points precisely reconstructs the road's true equivalent continuous level (LAeq) at the specified reference distance (e.g. 10 m), exhibiting true cylindrical line-source decay (−3 dB per doubling of distance).

Presets & Calibration Physics

Built-in Road Presets (LAeq at 10 m):

  • 🚗 Highway / Expressway: 78.0 dB(A)
  • 🚙 Arterial Road: 70.0 dB(A)
  • 🚐 Local Street: 60.0 dB(A)
  • 🚶 Pedestrian / Slow Zone: 50.0 dB(A)
  • 🚆 Railway: 80.0 dB(A)

Inputs (4)

  • Curve Paths (Curve list): Centerlines representing roads, avenues, or rail corridors.
  • Average Noises (Number list): Equivalent continuous level LAeq [dB(A)] at the reference distance from each road. Automatically matches list length or re-uses the last value.
  • Divide Length (Number): Target spacing in meters between emitter points. Thanks to analytical calibration, results are invariant to this setting.
  • Reference Distance (Number, optional): Perpendicular distance in meters from the road centerline at which the input dB level applies (default: 10.0 m).

Outputs (3)

  • Points (Point list): Generated 3D emitter points along the road corridors.
  • Noise Values (Number list): Calibrated point source levels Lp at 1 m [dB(A)], ready to connect directly into the Power(dB) input of Fast Noise Analyzer.
  • Info (Text): Detailed calibration notes, active point count, and acoustic methodology.

Method, assumptions and simplifications

The same notes appear in the component's Info output.

Method

  1. Each curve is divided into N = round(length / Divide Length) equal parts (at least 1); the actual spacing D = length / N is used.
  2. Each point gets a point-source level at 1 m, Lp1 = L_ref + 10 log10(D × RefDist / π), where L_ref is the Average Noises value for that curve (the last value is reused if the list is shorter).
  3. This comes from treating the road as a long straight line of incoherent point sources: summed intensity at perpendicular distance d is I1 × π / (D × d), so the field equals L_ref at RefDist and falls 3 dB per doubling of distance.
  4. The two end points of an open curve carry half a segment and get Lp1 − 3.01 dB; closed curves have no end correction.

Assumptions

  • Average Noises is LAeq in dB(A) at RefDist from the road (default 10 m, minimum 1 m).
  • Free-field spherical spreading (Lp1 − 20 log10 r) with energetic summation of incoherent sources, as in the Fast Noise Analyzer; its air absorption (2.8 dB/km) lowers the level at RefDist only slightly, and its ground effect (Ground supplied, G above 0) and barriers are not compensated, so L_ref at RefDist is reproduced only for hard ground and free view.
  • Model units are metres.

Simplifications and limits

  • Calibration assumes a long straight road; near the ends of short roads and on tight curves levels are slightly off.
  • No ground absorption, barriers, traffic composition, speed or road surface: those must be built into the input level.
  • Receivers closer than about one spacing to the road can see local hot spots near individual points.

Workflow

  • Road or rail centrelines -> Curve Paths; typical LAeq at 10 m from the value list (Highway 78, Arterial 70, Local 60, Pedestrian 50, Railway 80 dB(A)).
  • Points and Noise Values -> Fast Noise Analyzer (Power(dB) input).